clamping ball: stainless steel 440B (1.4112), hardened and ground.
Characteristics:
for centering and clamping in blind holes of components with locating holes;
precise self-centering with a precision of ±0,025 mm;
components with raw or machined surface can be centered positively and are pulled down on the contact points due to the ground clamping elements;
the centering clamping element is characterised by large setting ranges and a compact construction height;
HE49.0006.1170 and HE51.0006.1450 can be adjusted from above without SW1, with set screw and threaded end;
d3 is 1,5 at .1170; 2,0 at .1450; 2,5 at .1850; 3,0 at .2250 - .2650; 4,0 at .3050 - .4650; 5,0 at .5450 - .8650;
d4 is 5,0 at .1170; 6,0 at .1450; 8,0 at .1850; 10,0 at .2250 - .2650; 12,0 at .3050 - .4650; 14,0 at .5450; 16,0 at .7050 - .8650;
L1 is 10,0 at .1170; 12,0 at .1450; 14,0 at .1850; 15,0 at .2250 - .2650; 20,0 at .3050 - .4650; 32,0 at .5450; 20,0 at .7050; 25,0 at .8650;
L8 (slag in millimeter) is 1,4 at .1170; 2,3 at .1450 - .2650; 4,6 at .3050 - .4650; 9,3 at .5450 - .8650;
L9 is 3,5 at .1170; 4,5 at .1450; 5,5 at .1850; 7,0 at .2250 - .2650; 9,0 at .3050; 11,0 at .3850 - .4650; 15,0 at .5450; 17,0 at .7050; 25,0 at .8650;
l is 2,0 at .1170; 2,5 at .1450; 3,5 at .1850 - .3050; 4,5 at .3850; 6,5 at .4650 - .8650;
l1 is 3,5 at .1170; 5,5 at .1450; 7,5 at .1850; 6,0 at .2250 - .2650; 7,0 at .3050; 7,5 at .3850 - .4650; 9,0 at .5450; 10,0 at .7050 - .8650;
l2 is 3,5 at .1170; 4,5 at .1450; 5,5 at .1850; 7,0 at .2250 - .2650; 9,0 at .3050; 11,0 at .3850 - .4650; 15,0 at .5450; 17,0 at .7050; 25,0 at .8650;
x (diameter van de kogel) is 2,5 at .1170; 4,0 at .1450 - .2650; 8,0 at .3050 - .4650; 16,0 at .5450 - .8650;
x1 is 3 at .1170 - .3050; 6 at .3850 - .8650;
SW1 is 5 at .2250; 6 at .2650 - .3050; 8 at .3850 - .4650; 10 at .5450; 12 at .7050 - .8650;
d1, d4, L in the table represent the bore;
bore d1 in the table has a tolerance of H7;
F1 (kN) in the table represents the maximum clamping force.
Assembly:
take-off clamping plate and screw; fasten body by means of threaded pin via SW1.
Operation:
operation from bottom manually or automatically with either pneumatic or hydraulic actuation.
